ath10k_ahb a000000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-nvmem max-sta 32 raw 0 hwcrypto 1 Now plug in your flash drive to the ZTE usb port (flash drive has to be pre formatted with FAT or NTFS formatting, I used NTFS) The Elisa firmware gives generally more information on things in regards to signal, cell id etc. Also it gives you samba options (not that I'd use that personally) and reboot scheduling.

Updating the modem firmware looks intriguing, running a cut down version of android like the pinephone ec25?End of /etc/preinit_zte********************* 9.283014] random: procd: uninitialized urandom read (4 bytes read, 66 bits of entropy available) When trying to add a software update for MTS Russia, we will receive an error because we are trying to upload incompatible software. Now to get where you need to for the upgrade power the zte board off and then on again and in the putty console window you'll see an option to cancel the kernel boot process in uboot by pressing escape, you have to be fast to catch this though so if you miss it power off and then try again.

Like if there are 5 phones connected to it and then i want to limit only phone 1, 2 and 3 at 1 Mbps… but let the phone 4 and 5 have maximum Mbps? Reply home/scl/ci/workspace/Soft4_MF286D_H3GSE_CPE/build_folder/qsdk/build_dir/target-arm_cortex-a7_uClibc-1.0.14_eabi/linux-ipq806x/zte_genl_kernel-1.0/zte_genl_kernel_main.c[173]: INFO:send msg to user ok, cmd=3, msg=401 Kirjoita internetselaimesi osoitekenttään 192.168.100.1 ja paina Enter. Näin pääset laitteen hallintasivulle. Tämän voit tehdä vaikka internetyhteyttä ei olisikaan. Tämän jälkeen ohjaudut mobiilireitittimen hallintasivulle. Kirjaudu sivulle käyttämällä salasanaasi. Salasana on reitittimen langattoman verkon (WLAN/ WiFi) salasana.cfg init, /home/scl/ci/workspace/Soft4_MF286D_H3GSE_CPE/build_folder/qsdk/build_dir/target-arm_cortex-a7_uClibc-1.0.14_eabi/linux-ipq806x/cfg-1.0/cfg_param.c 583 home/scl/ci/workspace/Soft4_MF286D_H3GSE_CPE/build_folder/qsdk/build_dir/target-arm_cortex-a7_uClibc-1.0.14_eabi/linux-ipq806x/zte_genl_kernel-1.0/zte_genl_kernel_main.c[173]: INFO:send msg to user ok, cmd=1, msg=0000 Yes that was my mistake, I thought the root_uImage was mtd9 only, next time I'll "read the question" ol_swap_wlan_memory_expansion: length:152475 size_left:152495 dma_size_left:262144 fw_temp:d5379004 fw_entry_size:152499 My passion is helping people to get the most out of their mobile phone. I've been blogging at Ken's Tech Tips since 2005.

very interesting... I just factory reset the router. after the reboot the default language is not english anymore. It looks like it has the Elisa firmware flashed? Hello, so i am at the same point, the CP2102 i bought doesn't give me any output on Putty, and after followed some advices in OpenWRT forum, i got Nordic V11, and now the framework says is not a proper version. Toimi näin: Laitteelle kannattaa tehdä uusin päivitys tämän kuvallisen ohjeen mukaan. Huomaa, että tämän pystyt tekemään, vaikka internetyhteyttä ei olisikaan. Jos tämä ei auta, kannattaa kokeilla vielä laitteen tehdasasetusten palautusta. Kuvallisen ohjeen löydät täältä. You want to get the biggest SIM card – the standard-sized one. Be careful to avoid punching out the smaller micro or nano SIMs from the card.

Conclusion

Use openwrt.org, point on firmware selector and then select "snapshot" and mf286d. At the moment fw is distributed as a snapshot without luci (gui). After next branchout (version 21.02.03) fw will be available with luci at once. while this is for the MF286C (probably the US version), I suspect that the antenna design is similar if not identical on the MF286D. bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. ath10k_ahb a800000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' After configuring your LTE modem, you can follow Basic configuration to proceed with other configuration steps, such as setting up your Wi-Fi.