Yeah, I have the same issue. Using QL fans all over. I have to go in to the H150i to be able to change anything and the Commander Core is gone from the ICUE How does this compare your internal case or room temps? Most people will idle about 4-7C above the room temp, but this is very case and power level specific. Someone with a TR on High Performance in a glass box is going to be quite high, while an old Sandy Bridge that drops to 0.60v and stays there will be quite low. This seems to be where you are losing ground. It's a 900mb install, that really should have been broken into selective components and it's a real CPU and disk activity hog. I'm still using CorsairLink 4.9.6.19. It's a 45mb install, uses 0.3 - 0.7% cpu and tells me everything I need to know - my temps across all components, including disk drives (4.9.7.35 took that feature out), and my 14 fan speeds. I use 2xcommander pro on my system. iCUE software gives you the power to control and synchronize your cooler’s RGB lighting with all iCUE compatible devices, monitor CPU and coolant temperatures and adjust fan and pump speeds, all from a single intuitive interface.

ELITE LCD GIF Gallery - Corsair Community ELITE LCD GIF Gallery - Corsair Community

Intel 1700, Intel 1200, Intel 1150, Intel 1151, Intel 1156, Intel 2011, Intel 2066, Intel 1366, AMD AM4, AMD AM5, AMD sTR4 Harness the power of iCUE with the included iCUE Commander CORE to control the fan speed and RGB lighting for the included ML RGB fans, with the potential to control additional CORSAIR RGB fans, up to a total of six. I have QL fans everywhere - only the keyboard and RAM light up, and I cannot see any profiles anywhere to edit.

EFFICIENT AND SILENT CPU COOLING

With the side panels off and at idle, the coolant temp reaches about 34.5 C (Balanced preset) or 38-39 C (relaxed custom curve). So about 2 C cooler. Harness the power of iCUE with the included iCUE Commander CORE to control the fan speed and RGB lighting for the included ML RGB fans, with the potential to control additional CORSAIR RGB fans, up to a total ofsix. Also, setting to a decibel 'value' also isn't entirely accurate and can leave a larger range for operational limits. Example, there might actually be a variation of +/-300 RPM where the measurable difference of a single decibel is seen, but 300 RPM is actually a significant difference in the amount of airflow being moved. 1200 RPM and 1500 RPM actually end up performing quite differently. It becomes difficult to replicate test runs without variables based on decibel levels alone as the same measurement of 35dB for one test can easily fall outside of acceptable deviation. The power and fan cables come out from the top side of the water pump. This is not the cleanest approach when it comes to cable management. It would be nice to have a detachable fan cable if the user decides not to plug the fans directly into the water pump.

High Elite Capellix Coolant Temps? - Corsair Community High Elite Capellix Coolant Temps? - Corsair Community

Another question to all if I may ... are QL Fans supported on the Commander Core that came with the H150i Elite cooler? I put the ML's that came with the kit on to a separate Lighting Node Core, and attached the QL's to the Commander Core. QL's are selectable as an option, but not sure if they are fully supported.

Specialized Cooling Modes

This is great in concept, except that the reality is that not every cooler manages to reach the same dB level at peak operation or lowest noise levels as every other cooler. Some coolers are not seen to operate at 35 or 40dB while others easily exceed it. These same coolers in comparison also iCUE will update your device firmware. Do NOT disconnect your device while the update is happening. The gpu will certainly heat up the inside so the Cyberpunk results don’t surprise me. The prolonged time after gaming at high temps suggests environmental heat, but can also be a restricted cooler. How does the 48C compare to something like the motherboard sensor or any other internal temp data?