Conclusion: Although the 635-216 is smaller than the 10 XC, it comes surprisingly close in terms of rip capacity and cutting height. The 10 XC will still support your workpiece better, and provide a bit more power. Miter Gauge vs Sliding Table Miter gauge on the 635-216 The TS 254 M actually comes with such a support bar included, made of the same material as the table top. It is sloped so you can use it for angled cuts as well. Another thing it has over the other two saws is that it can be adjusted for play. There are two screws or bolts that you can turn to make it slightly wider or narrower. This makes it fit exactly in the miter slot, eliminating any sideways movement. The particularly stable rip fence made of die-cast aluminium ensures high precision: It is attached to the front and rear of the table saw with a double clamp and thus sits reliably with every cut. But it is also more than twice as expensive. This makes the GTS 635-216 very good value for money. It may not be as well built, or have as unique features at the 10 XC, it can cut almost the same height and rip the same width. With some attention, you can achieve the same results on the 635-216 as on the 10 XC, but for less than half the money.

So, given the larger and heavier table, your workpiece will be better supported on the 10 XC. But if you really want to, you can make the same large cuts on the small 635-216 as you can on its larger brother. 635mm is large enough to cut a standard sized plywood sheet in half on the short side. Power Jediná vada na kráse byla, že vnitřní část s motorem byla pro účely přepravy výrobcem fixována umělohmotnou páskou, která se ovšem během přepravy přetrhla, takže motor + vnitřní pohyblivý mechanismus měl možnost se mlátit sem a tam. No ale po prohlídce se naštěstí nic nepoškodilo. Build quality is always hard to judge from the outside, and can really only be proven after using a machine for a few years. Given that all three saws are quite new, we’ll have to wait some time to see what actual users report when using the machines for some time.As a result, the 635 can cut up to 70mm high, compared to the 79mm of the GTS 10 XC. This difference is actually surprisingly small. Most 216mm saws can cut less than 70, and most 254mm table saws can cut higher than 79mm. In this case, the bigger machine doesn’t have a big advantage. I have to agree with the noise issue, it’s definitely the main reason why I don’t use it as much as I wanted to. Having my shop in the basement of my apartment building means I can’t bother people too much. And this saw is anything but quiet. Wish I waited longer and saved more money so I could buy a saw with an induction motor. This one’s super loud. Way too much for a modern saw, imho. The GTS 635-216 Professional is the compact, yet powerful, table saw for multi-purpose use. Its 1,600 W motor power is ideal for a cutting height up to 70 mm and for a rip capacity up to 635 mm. The low weight of only 22 kg, its ergonomic handles, and protective on-board storage make transport genuinely easy and safe. The table saw works extremely precisely and, due to its integrated slide carriage, table-widener, and table extension, it is exceptionally versatile. Equipment & Application The most obvious difference between the two is that the 635-216 is smaller. It has a smaller body and smaller blade. Saw Blades and Cutting Height The miter gauges on these three saws are similar. They are all quite basic, and have no stops that can be set to ‘remember’ specific angles. This means every time you change the angle, you’ll need to re-measure to make sure it is accurate.

Tuto pilu rozhodně doporučuji všem, kdo pracují se dřevem, protože výsledky práce jsou skvělé a poměr cena / výkon více než dobrý.That being said, the Bosch does seem to be the most plastic-y of the three. But it also has more body, while the other two have more of an open body design. Special event, club or membership offers, third party promotions or prices not available to the general public Compared to the PTS 10 T, it is made from higher quality materials, more accurate, and slightly more powerful. It is also a bit smaller, and can be much easier carried around, because it is 10kg lighter. Fence Conclusion: Overall, the Metabo has an advantage in dealing with solid wood, thanks to the larger saw blade. The DeWalt and Bosch on the other hand are slightly better if you plan on cutting large sheet goods. Build Quality Pila je skutečně o několik úrovní nad těmi, které jsem dosud měl. Umožňuje přesné a spolehlivé řezy, protože se všechny parametry dají přesně seřídit. Výkon motoru je dostačující, nastavení bočního dorazu je opět velmi jednoduché a exaktní a doraz je fixován jak zepředu, tak i ze zadní strany.

With a saw blade diameter of 216 millimetres, it is the best in its class. This is based on the special design of the new table saw: The arrangement of motor and gearbox has been optimised so that the saw blade protrudes further than with conventional table saws ‒ and thus achieves more cutting height with a smaller blade. Where the GTS 10 XC does have a clear advantage, however, is in terms of power. Its 2100 Watt motor will help with cutting tough hardwoods like oak and maple. Especially when you get close to the maximum cutting height, the extra 500 Watt compared to the 635-216 (1600W) can be really helpful.

While the GTS 635-216‘s miter gauge is made of plastic, the DWE7485 supplies a metal miter gauge, which feels like it will last for longer. The DeWalt’s miter gauge also has some holes to which you can add your own wooden or metal bar to make it bigger and more stable. The 635-216’s gauge does not have this. However, the rip capacity is actually the same on both saws! Both the GTS 10 XC and 635-216 have a rip capacity of 635mm. This rip capacity also explains the other part of the name (635). The GTS 10 XC is significantly heavier at 35kg, compared to 22kg of the 635-216. Total Tools reserve the right to terminate or amend the price guarantee policy at any time without notice. For Further Information The accuracy of a table saw depends on three main factors: the fence, miter gauge, and the general flatness/dimensions of the body. If the fence isn’t straight, or moves out of parallel with the saw blade, you’ll never make accurate rip cuts. Given the DeWalt’s premium price, you’d expect it to have a better internal build quality too, but it’s hard to tell if that is really the case.