ECO RACK MOBILE DRYING RACK for PAINT SPRAY SHOPS

Product Information

ASCE. 2016. Minimum Design Loads and Associated Criteria for Buildings and Other Structures. ASCE/SEI 7-16. Reston, VA: ASCE. The variety and availability of equipment used to apply water are sometimes not thought through. Water testing with a thumbed hose is an all-too-common approach. The author recommends that contractors and design professionals alike keep a variety of water application tools in their toolkit. Furthermore, ASTM D5957 should primarily be used as a performance assessment. Flood testing used as a diagnostic tool is generally ineffective—it indicates that a problem exists but not necessarily what that problem is or where it might occur in the assembly. If flood testing is used diagnostically, it requires that each penetration, transition, and area be isolated and tested separately. If flood testing is not practical or desired, the reader is directed to electronic leak detection standards, namely ASTM D787721 and ASTM D8231. 22

six-foot poles, 1 spray tube, 6 bases, joints and hardware to build the spraying and drying stands. AAMA. 2011. North American Fenestration Standard/Specification for Windows, Doors, and Skylights (NAFS). AAMA/WDMA/CSA 101/I.S.2/ A440-11. Schaumburg, IL: AAMA. Hang doors by common cup-hooks or use Hinge Hooks or EFC Hooks for completely unmarred surface results. The doors then hang on the spinner assembly, which is designed to give the painter complete control of the hanging part. Heavy-duty metal hangers eliminate the annoying and costly failure of wooden clothes hangers. 18 feet of drying line allows tight spacing of 50 drying doors since the custom hanger hook radius matches the drying pole, preventing parts from spinning.Even a typical multipurpose garden sprayer can be a step up from a thumbed hose. Although not a scientific approach, a sprayer provides some level of repeatability and control of water application. Further, a small brass bull’s-eye nozzle ( Fig. 1) can be effective in directing small amounts of water to specific locations. Figure 2. Monarch B-25 nozzles. ASTM International and the American Architectural Manufacturers Association (AAMA; now known as the Fenestration and Glazing Industry Alliance) have published a number of documents related to testing building enclosure assemblies. These documents and standards, when read individually, provide tremendous guidance for specific procedures. However, there are few documents that compare and contrast the equipment, techniques, and conditions involved with each procedure. AAMA 511, 1 in conjunction with ASTM E2128, 2 provides some guidance on the diagnostic front, but it does not connect this information with performance testing. AAMA 501 3 provides further guidance on the array of available testing methods for assemblies and fenestration. Please note that our products are handled and delivered by national pallet networks so they may be loaded and unloaded from vehicles several times before they are finally delivered to you. This may result in products being marked, scuffed or the paintwork being lightly scratched while being handled by forklifts. These cosmetic imperfections do not impact on the durability or safety of the product. It should be noted that the ASTM E1105 appendix mentions that the water-spray volume is not tied to a specific rain event. In fact, the comparison between any given event and water-spray volume is misleading. The water spray is intended to fully and uniformly wet the entire exterior for the duration of the test. This purpose ultimately leads to an overwhelmed weep system, which is then exacerbated by the differential pressure. This test is intended to completely inundate the specimen’s water management system and is not “intended to reproduce or simulate any given rain event.” For windows with sills that can collect water, the test will necessarily produce standing water (in the sill), whose depth is proportional to the differential pressure applied.

As a general rule for any tiered or staged water testing, the lowest area under consideration should be tested first. This is explained in both AAMA 501.2 5 and ASTM E2128. 2 As noted in ASTM E2128, “starting at the bottom helps eliminate ambiguity about the origin of a leak that might result from water running vertically down the surface of the test area.” Additionally, testers should take care to not overspray the area being tested, as this can lead to false positives and misunderstood results. For flood testing, it is necessary to understand that the weight of water is 5.2 lb/ft 2 (250 Pa) per inch of depth. That is, 4 in. (100 mm) of water—the maximum depth allowed by ASTM D5957 18—equates to over 20 lb/ft 2 (1000 Pa). This pressure is the structural design live load for unoccupied roofs. Explicitly, the maximum water depth allowed per ASTM D5957 is intended to match a typical minimum structural design load. diagnostic testing, which is used to evaluate observed water intrusion and attempts to re-create leakage. AAMA. 2013. Recommended Static Water Penetration Resistance Test Pressures in Non-Hurricane-Prone Regions of the United States. AAMA TIR-A13-13. Schaumburg, IL: AAMA. The PSDR Series is an integrated system that uses cabinet door hangers for painting. It's designed to paint and dry cabinet doors in a vertical orientation with the least amount of effort and space. Cabinet door hangers are used for spraying all sides in one step.Lastly, it is important to consider how wind pressures are calculated. ASCE 7-05 23 has been the mainstay for wind pressure determination, particularly in AAMA 511, 1 which references ASCE 7-05 procedures to determine differential pressures across a specimen. However, current structural codes have adopted ASCE 7-16, 24 and there are notable differences between the ASCE 7-05 and ASCE 7-16 editions in their quantitative approaches to converting wind speeds into wind design pressures. We cannot accept the return of any products engineered or manufactured to the customer’s bespoke requirements other than where a product is found to have a material defect arising directly from its manufacture. An additional point is that all AAMA tests require an AAMA-accredited independent testing agency (see guidelines in AAMA 204 20). AAMA tests conducted by nonaccredited agencies should therefore be considered “modified” as they do not comply with the accreditation requirement.

performance or quality assurance testing, which is used to ensure the performance of a recently installed assembly or determine the in-field rating or performance of an unrated unit, and When comparing testing procedures between ASTM E1105 8 and AAMA 502, 11 the investigator realizes that ASTM E1105 requires a minimum of three 5-minute pressure cycles (“In no case…shall the total time of pressure application be less than 15 minutes”) whereas AAMA 502 requires “four cycles.” Given these discrepancies, the investigator is best served to perform four cycles so as to satisfy both requirements. For example, if a window’s water penetration resistance rating is a pressure of 2.0 lb/ft2 (99 Pa), then its sill would be filled with 3/8 in. (10 mm) of water. This correlation is related to the density of water, 62.4 lb/ft 3 (9.9 kg/m 3) or 5.2 lb/ft 2 per inch (9.9 Pa/mm). The depth of water can be calculated by dividing the intended pressure by the density of water. That is, 2 lb/ft 2 / 5.2 lb/ft 2 per inch (9.9 Pa/mm) of water = 3/8 in. (10 mm) of water. This is the same amount of water that would appear in the sill if the specimen were tested with the ASTM E1105 method using a differential pressure of 2 lb/ft 2.

The Prism Range

A B-25 nozzle is a brass adapter ( Fig. 2). Its use is standardized in AAMA 501.2.5 It sprays a mid to high volume under relatively high pressure (the volumetric rate is unspecified but is intended to be used at 35 psi [240 kPa]). When applied 12 in. (305 mm) from and perpendicular to a surface, the spray pattern is circular with an 18- to 24-in. (460- to 610-mm) diameter. This nozzle is intended for solo use and is typically attached to a PVC or metal wand for application.

Please ensure that your premises are open to accept your delivery between the hours specified. If your premises are closed when a delivery is attempted, you may be charged a re-delivery fee.All deliveries are made using the UK Pallet Network. These deliveries are made using 2.5 ton or Heavy Goods Vehicles.