Cisco Catalyst 1000-8P-2G-L Network Switch, 8 Gigabit Ethernet (GbE) PoE+ Ports, 670W PoE Budget, two 1 G SFP/RJ-45 Combo Ports, Fanless Operation, Enhanced Limited (C1000-8P-2G-L)

Product Information

Cooling mechanisms, such as fans and blowers in the switch, can draw dust and other particles causing contaminant build-up

member number of 1. When it joins a group, its default number changes to the lowest available number in the corresponding To prevent airflow restriction, allow clearance around the ventilation openings to be at least: 3 in. (7.6 cm) Statement 1076 It provides you with the ability to automatically upgrade the internal flash with the USB drive's configuration and imageAlign the module in front of the slot opening, and push until you feel the connector snap into place. Before you install the switch on a wall, or on a table or shelf, power on the switch and verify that it passes POST. Loosen the number-10 Phillips pan-head screws, slide the cable guide out, and pivot it upwards so that you can install the support with Network Edge Access Topology (NEAT), which extends identity authentication to areas outside the wiring closet (such as conference rooms). Configuration Guides• Software Configuration Guide, Cisco IOS Release 15.2(7)Ex (Catalyst 1000 Switches) 25-Dec-2019

Use the screw template to align the mounting screw holes and also as a guide to make sure that you install the screws into mm) holes at each of the two mounting locations. Insert the supplied 0.5 in. (12.7 mm) number-8 Phillips wood screws This section describes the rear panel components of Cisco Catalyst 1000 24-port and 48-port switches.

Deploy secure intelligent switching with Cisco DNA software

or Category 5e twisted pair (UTP) cable. The 10BASE-T traffic can use Category 3 or Category 4 UTP cable. of RX (received data) is reversed. Normally, one differential signal includes "+" and "-", and RX+ connects to TX+, RX- connects After a successful POST, unplug the power cord from the switch and install the switch on a wall, on a table, or on a shelf. Depending on the switch model and the number of PoE ports, the maximum switch power output varies. For the 24-port switch Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040

IP Phones and wireless access points, IEEE 802.3af, or 802.3at (PoE+) compliant devices. You must remove any cable or device of the desk or shelf. This ensures that the power cord faces the rear of the desk or shelf after the switch is installed. IEEE 802.1AX,IEEE 802.1D,IEEE 802.1Q,IEEE 802.1ab,IEEE 802.1p,IEEE 802.1s,IEEE 802.1w,IEEE 802.1x,IEEE 802.3,IEEE 802.3ab,IEEE 802.3ad,IEEE 802.3ae,IEEE 802.3af,IEEE 802.3ah,IEEE 802.3at,IEEE 802.3az,IEEE 802.3u,IEEE 802.3x,IEEE 802.3z When medium dependent interface (MDI) on peer devices do not have the Automatic Polarity Correction feature, the C1000-24T-4G-L Device management support with over-the-air access via Bluetooth, Simple Network Management Protocol (SNMP), RJ-45, or USB console accessThe software features supported on the Cisco Catalyst 1000 Series can be found on Cisco Feature Navigator: https://cfn.cloudapps.cisco.com/ITDIT/CFN/jsp/by-feature-technology.jsp. Catalyst 1000 series Fast Ethernet models are available with LAN Lite equivalent feature set only. Fast ethernet provide reduced functionality and scalability compared to the Gigabit ethernet models and are targeted for deployments with basic requirements. Use the supplied number-10 pan-head screws to attach the cable guard to the switch. Figure 19. Attaching the Cable Guard to the Switch Cisco Catalyst 2960-L Series Switches are fixed-configuration, Gigabit Ethernet switches that provide entry-level enterprise-cla

Insert two screws in the slots on the screw template, and tighten them until they touch the top of the screw template. Figure 3. Installing the Mounting Screws on Top of a Desk or a Shelf If the same number is used by another member, the device selects the lowest available number in the group. The AC frequency range of the power supply is 50Hz/60Hz. Plug the AC power cord into the AC power connector and into an AC If you insert a 10G SFP+ in to a 1G SFP module slot and vice versa, you need to clear the existing configuration by running

One of the remaining member switches becomes the new active switch. All the other member switches in the group remain as To prevent airflow restriction, allow clearance around the ventilation openings to be at least: 3 in. (7.6 cm) Statement