HP JL258A ARUBA 2930F 8G POE+ 2SFP+ SWITCH

Product Information

For J9263A, J9264A: K.14.03 (for J9054B/C 1990-3613); K.15.08.0007 (for J9054C 1990-4112 and 1990-4483) X122 1Gb SFP LC BX-D transceiver - Small Form-factor Pluggable (SFP) Gigabit BX (bi-directional) 'downstream' transceiver that provides a full-duplex Gigabit solution up to 10km (6.21 miles) on one single-mode fiber - Has one LC 1000BASE-BX10 port

speed is NOT supported for the J8177D or JL747A when used in any port (SFP+, SFP28, or SFP56) on the 6400 series. Idle power is the actual power consumption of the device with no ports connected (not applicable to the 8G switch). Premier Flex Multimode OM4 LC/LC Fiber Optic cable, 15m (49.2ft) long - Duplex zipcord graded index 50/125um multimode 'bendable' fiber optic cable with LC/MPO connectors on each end (Blue Color) - Optical performance: 4700MHz/km For use in the SFP ports of the 2530 Series Switches. (The J9853A, J9854A, J9855A, and J9856A models have 1G/10G SFP⁠+ ports that do not support these 100Mbps transceiver modules.)The 8325 requires configuration of "interface groups" (groups of 12 ports) to enable use of 1G or 10G transceivers or DACs in the SFP28 ports (default is to use 25G transceivers / DACs). See the RJ-45 autosensing 10/100/1000 PoE+ ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T, IEEE 802.3at PoE+); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only 2 SFP+ 1/10GbE ports; PHY-less The 2930F Switch Series models with 1G/10G SFP⁠+ ports added support for this J9054C/J9054D 100FX transceiver. The J9054C/J9054D are supported in models with 1G SFP ports. LLDP-MED (Media Endpoint Discovery) defines a standard extension of LLDP that stores values for parameters such as QoS and VLAN to automatically configure network devices such as IP phones

RJ-45 autosensing 10/100/1000 PoE+ ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T, IEEE 802.3at PoE+); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only Only the J8177D is supported (J8177C not supported). J8177D or JL747A can only operate at 1G in the 10000 series.

The link state of ports on the JL687A module will always show UP if a transceiver is inserted and the interface is enabled, even if the cable is disconnected EN 55032:2012/CISPR 32 Class A; FCC CFR 47 Part 15 Class A; VCCI Class A; ICES-003 Class A; CNS 13438 Multimode OM3 LC/LC Fiber Optic cable, 50m (164ft) long - Duplex zipcord graded index 50/125um multimode fiber optic cable with LC connectors on each end (Aqua Color) - Optical performance: 2000MHz/km X122 1Gb SFP LC BX-U Transceiver - Small Form-factor Pluggable (SFP) Gigabit BX (bi-directional) 'upstream' transceiver that provides a full-duplex Gigabit solution up to 10km (6.21 miles) on one single-mode fiber - Has one LC 1000BASE-BX10 port CAT 5e cable RJ45 to RJ45 7.6m (25ft) - Up to 1 Gigabit operation, Ethernet cable with (M) RJ45 connectors on each end