Rust-Oleum White Scratch-Proof Floor Paint in Matt Finish - Chalk White 2.5L

Product Information

Stain Removal: Remove any stains promptly, most common stainse.g. dirt, ketchup, mustard, tea, coffee can be removed using a softcloth and warm soapy water. Do not use scourers or abrasive cleanersas these may mark the paint finish. Drying Time: Touch dry in 2 hours. Apply a second coat after 2 hoursif necessary. Hard dry in 4 hours, full hardness achieved after 7 days.

The Rust-Oleum Chalky Finish Floor Paint is water-based with virtually no odour and give an extremely durable smooth matt finish. We will be happy to organise an exchange for the correct goods at no extra charge to yourself, please get in touch to organise this. Faulty ItemsWhile a small hand sander or orbital sander can be useful for preparation, if you have a large space with previously painted or stained floorboards, you'll likely need to hire a drum sander for sanding floorboards properly. After you have finished preparing your floorboards you need to think about draughts. If you can live with the draught that comes up between the gaps in your floorboards then leave. But it makes much more sense to seal the gap to stop cold draughts and keep your heating bills down. Limitations: For interior use only. Temperature at time of theapplication and during drying should be greater than 5°C. To ensurepaint suitability for your particular project test on a small inconspicuousarea first. Now vacuum the floor to get rid of as much dust and debris as possible. The final part of the prep is to clean the floorboards. Use a mop and liquid detergent (as instructed). Then rinse with the mop and clean warm water and leave to dry for at least 24 hours. Use a primer or specialist paint to cover any knots or stains.

Application: Stir thoroughly prior to use. The product may be appliedby brush or medium pile roller. Preparation: For best results, ensure surface is clean and free from wax or oil. If wax has been used clean the surface thoroughly with white spirit. We recommend that bare wood should be sanded before painting. Preparation: For best results, ensure surface is clean and free from wax or oil. If wax has been used clean the surface thoroughly with white spirit. We recommend that bare wood, previously painted or varnished surfaces should be sanded before painting. Ensure new concrete is sound, fully cured and free from laitance.

Filters

Clean Up: Remove as much product as possible from application equipment before washing with water. Do not empty into drains or water courses. Some local authorities have special facilities for the disposal of waste coatings. A luxurious durable matt finish for interior walls and ceilings.Class 1 scrub rated for easy cleaning. Scuff and stain resistant. Obviously, a floor that is well prepped and painted and has low traffic will last longer. And even after a couple of years you are unlikely to need to repaint the whole floor, just the areas that get a lot of use. A Finally, adding an extra coat of your chosen paint or a clear matt varnish can give your floorboard paint a longer life. What's the Best Floor Paint?

Application: Stir thoroughly prior to use. The product may be applied by brush or roller. If applying by bush, apply evenly following the grain of the wood. If rollering, use a nap mohair roller. To create a distressed look apply two coats in contrasting colours. Allow to dry then lightly abrade with moistened sand paper or a stainless steel scouring pad - abrade with the grain of the wood. Protect the effect with Rust-Oleum Furniture Finishing Wax. Coverage: Up to 12 - 14m2 / litre. Coverage may vary depending upon method and rate of application and porosity of surface. Painting floorboards with a paint pad can be effective. (Image credit: Ronseal) How Long Will a Painted Floor Last? One simple way to extend the lifespan of your painted floor is to make sure that the floorboards are prepped properly. The more time spent on this part of the process the better the end product will be. Drying Time: Touch dry in 1 hour. Handle after 4 hours. Apply a second coat after 4 hours, if necessary. Full hardness after 4 hours.Coverage: Up to 12m²/l per coat. Coverage may vary depending uponmethod and rate of application and porosity of surface.