Autoglym Polar Collection - Car Cleaning Kit Includes Polar Blast Pre-Wash Snow Foam, Polar Wash Car Shampoo, and Polar Seal Pressure Wash Coating

Autoglym Polar Blaster Snow Foamer

If the thought of adding a ceramic coating to your car scares you, or you want that deep shine traditional waxes offer, Autoglym has you covered. For the ultimate shine, our top choice is Autoglym Ultra High Definition Wax. It'll give your car a mirror-like finish thanks to the use of refined carnauba wax and comes with a handy applicator and buffing towel. Alternatively, there's Rapid Aqua Wax, a budget carnauba wax that can be applied to all exterior surfaces, including glass and rubber. Aiming at the floor, pull the trigger on your pressure washer, allowing the Polar product to feed through. The Polar Blaster has been designed and tested to be used specifically with the three Autoglym Polar products. It will enhance their foam levels, dwell time and coverage. The cleaner will begin to loosen dirt on all surfaces. For the most thorough clean we recommend agitating the foam with a sponge or wash mitt. The Autoglym Polar Kit contains 3 products used via a pressure washer to maintain & protect your vehicle.

The Polar Blaster is a foam cannon that can be attached to domestic pressure washes to enhance the foam levels and user experience of the three products in the Autoglym Polar range. It fixes to the lance and comes with a bottle reservoir that contains the dilute product, negating the need to place a fill pipe in the product bottle.

Polar Blast can be used at various dilutions depending on the density of foam desired. A good starting point is 100ml product to 500ml water in your foaming bottle. Adjust foam gun settings as required to increase or reduce foam. Polar Wash is a safe and effective cleaner applied after using Polar Blast to remove excess dirt, traffic film and grime from your paintwork. data-src="https://cdn.media.amplience.net/i/washford/haluk-car-cleaning-spot1-step3-process-winter21-1382x867" We would not recommend agitation as part of a pre-wash process. Allow the product to dwell on the paintwork for up to 10 minutes. This will allow Polar Blast to safely soften and loosen soiling, before rinsing with your pressure washer. Dilute the product at the recommended rate, outlined on the sidewall of the Polar reservoir bottle (D).

Polar Seal contains silicones, which in some cases, can create smears once wiper blades are used on the windscreen. We would recommend cleaning your windscreen after you have applied Polar Seal to the rest of your car as part of your car cleaning process. Polar Blast is used as a pre wash snow foam and produces a highly dense foam blanket to your vehicle to help maximise cling time and loosen dirt. We would recommend that only the product needed for a single application is used. We also recommend that the foamer bottle is rinsed thoroughly after use. Only a small amount of Polar Seal is required. Pour no more than 40ml (four capfuls) into your foam bottle and then add at least 200ml of water. This should be all the finished solution required to cover your vehicle. There is no benefit in using any more than 40ml as over application can compromise the finish.We recommend a pre-wash with Polar Blast to gently loosen dirt. If not, rinse first with water to loosen heavy contamination. Polar Wash can be used at various dilutions depending on the density of foam desired. However, we would not recommend using a dilution stronger than 50:50. Adjust foam gun settings as required to increase or reduce foam. 250ml of mixed solution should be enough to cover an average sized car. An exterior car care kit that makes the ideal gift for any budding car care enthusiast. Comprised of the three Autoglym Polar range products providing treatment for pre-wash, wash & protection. If your vehicle only has very light soiling and you are using in place of shampoo. Please rinse vehicle first before applying Polar Blast. You can either allow to dwell and rinse without agitation or agitate with a sponge or wash mitt prior to rinsing. In summary the product has been developed to work neat through to 1part Polar Blast to 10 parts water. We have been very happy with the product performance diluted at 1:5.

It is a coating designed specifically for use in a pressure washer. It is the coating element (third and final stage) of the three-stage Polar range process. It is preceded by the prewash – Polar Blast and shampoo - Polar Wash. Yes, apart from the front windscreen we would recommend Polar Seal can be used on all exterior surfaces. We recommend starting with a snow foam like Polar Blast to gently loosen dirt, and follow with Polar Wash to remove any dirt or contamination on your paintwork.There is no benefit to building layers of Polar Seal. We would only recommend reapplication once water beading has ceased. We certainly do not recommend application more than once a month. It is important that Polar Seal does not dry on to the surface of the vehicle. Once the car has been coated it should be rinsed immediately. Polishing your car is a great way to fade small scratches and imperfections. Find out how with our handy guide. This really is dependent on several factors including the level of foam you would like to achieve, the settings of your pressure washer and the hardness of water in your area.