STC-1000

Product Information

STC1000 from Elitech had completely different PCBs with other components than the generic STC1000.Here’s a comparison on photos: Generic is left and Elitech is right

Prevent potential off-flavors: When it’s too hot, the controller switches to cooling mode to regulate the temperature of your fermenter. Too hot a ferment speeds up yeast activity. This vigorous action can produce fusel oils and result in off flavors.F4:Temperature calibration:You can make the Stc-1000 very accurate, just compare the temperatures with a verified thermometer (best compare at the target temperature) you can increase or decrease the temperature after 0.1C steps. Zahrnujeme zelený terminál, dvě svorky 1-2 jsou pro napájení AC 110 / 220V (230V), svorka 3-4 pro teplotní čidlo, svorky 5-6 pro topné relé 7-8 pro chladicí relé. The first thing that is needed is to upload the sketch Before the connections are made from the Arduino to the STC-1000, the sketch needs to be uploaded to the Arduino. It is important that connections are not made before this. An unknown program running on the Arduino could set the pins to the wrong state and short circuit the STC-1000. This could damage your STC-1000 and/or your Arduino. Then the programming header can be inserted from the top of the board and soldered in place. This way you will have easy access the pins, making any future upgrades easier.

Upload attachment (Allowed file types: jpg, gif, png, pdf, doc, docx, xls, rar, zip, maximum file size: 2MB.

Penulis

STC-1000+ is an open source implementation of firmware(s) for the STC-1000 dual stage thermostat that add improvements and features over the version it is shipped with. It also provides an easy and cheap way of uploading said firmware(s) to the thermostat by emulating a programmer using the widely available Arduino platform. Finally the project adds a few tools that make it easier use and upload the firmware(s).

One key factor for lowest tooling costs and the highest productivity is the right process cooling selection. The STC machines offer all state-of-theart through spindle cooling options: Firmware built to control a single vessel brew system (for example Braumeister, Grainfather and similar systems/DIY setups). Read more here STC-1000+ RH (relative humidity controller) firmware Nejlepší použití digitálniho regulátoru teploty STC-1000 je v líhních, inkubátoru, péči o zvířata citlivých na správnou teplotu jako v akváriu. Je to dobré v kotlích pro ohřev vody nebo v chladničkách a mrazničkách, DIY projekty, byly použity v mnoha keezerech, kegerátorech a fermentorech. Podrobný popis termostatu STC 1000Viete mi poradiť ako to odstrániť? Je to vôbec možné, alebo sa to nedá. Deje sa mi to na všetkých termostatoch. Netvrdím že nie je chyba u mňa, ale nie som si vedomý kde ju robím. The Arduino Pro Mini + TTL USB addon is what I've been using. I like the complactness of the finished build, but I'd really recommend going with the Nano or UNO, as it is easier (and probably cheaper). The exact same thing as the normal STC-1000+ firmware, except profile is updated every minute instead of every hour. Same variations of extra featured versions. STC-1000+ OVBSC (one vessel brew system controller) firmware

The main visible difference is that the power supply to the Elite has a large brown while the generic version of the thermostat has smaller yellow with electronics around (which is better I do not know) Once the differences in weight were detected, I had to dismantleboht STC-1000 temperature controllers because it is definitely not a complete copy only with mark “Elitech”. Send 'a' or 'f' to upload the version you want (Celsius or Fahrenheit). If you are upgrading from a previous version of STC-1000+, you may want to use the 'b' or 'g' command instead. The difference is that all the data will be retained in EEPROM (i.e. profiles, temperature correction et.c.). When upgrading, the sketch will indicate (on the 'd' command output) if there are changes that might invalidate your current EEPROM data, and if so you might want to use the 'a'/'f' command even when upgrading, to make sure the data has sane defaults. Conversely, if it’s too cold, the STC-1000 will turn on your heater or heating pad. This will increase the heat of your fermenter to continue the fermentation process. Dimensions

Pros and cons

High pressure cooling for water-based coolants or oil (pressures up to 150 bar / 2175 psi psi to get as close to the cutting zone as possible) Under normal operating status, the panel displays currently measured temperature and automatically recognizes and switches cooling and heating modes. If you are considering purchasing a thermostat with a probe, you are sure to see the Elitech STC-1000,but does it differ from the generic “noname” version?In this review you will find a comparison with the generic version and a complete manual how to wirring and set up this temperature controller. Comparison with Elitech vs. Generic Version in Review Nyní popíšu termostat a ovládání, pokusím se přesně popsat. Zařízení STC 1000 obsahuje pět hlavních komponent: