Razer Panthera Evo: Fully Mod-Capable - Sanwa Joystick and Buttons - Internal Storage Compartment - Tournament Arcade Stick for PS4 and PS%

Product Information

Razer Panthera Evo will make its public debut at Evo 2018, the world’s biggest fighting game event. Each print is laser cut to your specifications, as presented by available options. You will receive the print with insert cutouts designed to fit your chosen brand. Gently press downward to remove the cutouts. Important Notes about Color Fidelity, Brightness Removing the original Razer pushbuttons requires disconnecting the wires that are attached to the .110" terminals on each button. It is recommended that you do not attempt to pull with a wrench or your finger; the design of the button microswitch can easily bend and distort from the force, possibly damaging the button terminals. Instead, use needle-nose pliers to grasp the disconnects by their tabs (circled in green), then squeeze in and upward. If the tabs are pressed in correctly, the disconnect should lift with just a bit of effort. If you find much resistance, retry pinching the pliers around the tabs and squeeze again.

Razer Support Hardware Drivers - Official Razer Support

You now need to get power to the Kaimana from the USB port. You'll notice that the USB wires are soldered/glued onto the board, and that there are five pins next to next to them. Take your remaining two jumper wires and plug them into the 1st and 4th pins going from top to bottom, like This. --- ALTERNATE VIEW Now, this may be worrying to some players, especially to fans of Sanwa like myself. It’s clear that Razer may have done this as some kind of cost-cutting solution. So that means they’re bad, right? Not necessarily. You see, I think Razer’s buttons work quite well – at least most of the time. Edit 2: Added photo of internal wiring per request, although it's pretty shabby... https://imgur.com/JD6UvjB Playing Dragon Ball FighterZ, the in-game button prompts were still Xbox controls, unfortunately. But, after a bit of getting used to, it’s easy enough to look past. But, once I was actually playing with the Panthera Evo, a few of the downsides showed themselves. Unless properly calibrated to your printer and viewing environment, your monitor does not accurately represent the brightness of paper. Artwork submissions may need adjustment to ensure prints are not too dark. Please read this helpful support article for more informationWe cannot replicate this panel, so when servicing the unit upside down, we recommend that you place it on a soft cloth or towel as it tends to scuff easily on hard surfaces.

RAZER PANTHERA KAIMANA LED MOD UPDATED 2019, NO - Reddit RAZER PANTHERA KAIMANA LED MOD UPDATED 2019, NO - Reddit

Then, daisy-chain your LED's and connect them to your Mini. Here is a great tutorial on how to do this: https://www.youtube.com/watch?v=mKty1h_pj54 In addition, we are unable to reproduce this Razer EVO panel in plexi due to its unique design, made by a plastic mold and curved. Because the button layout and control panel are baked into the panel, we do not offer button layout or control panel adjustment. It takes removing seven screws just to remove the front plate and change out the artwork. With that removed, it takes another nine screws to open up the chassis. Given that the original Panthera popped up with just the push of a button, this feels like a downgrade. Pushbutton manufacturers such as Sanwa, Seimitsu, Crown and GamerFinger have each produced specific models with a clear or translucent plastic cap and flat plunger. These are often used to display a graphical insert, allowing you to enhance the button's appearance. That said, each button manufacturer has designed the artwork cap with a different diameter than their competitors. For example, GamerFinger's artwork cap has a diameter that is slightly larger than Seimitsu or Sanwa. An insert cut for a Sanwa artwork cap will fit loosely when inserted into the GamerFinger artwork cap. This is an undesirable result that can produce a white or colored ring around the insert.DO NOT REMOVE THE FEMALE ENDS! Your wires should all look like this example wire by the time you're done. You now need to separate 11 of the Jumper Wires from each other, so you have 11 individual wires. You need to remove the Plastic Casing from the male ends of each wire. Often, you will have several options to personalize your control panel, such as button layout, removal of control panel or screws in some models, button label etching, and text etching.