Joined in 2023 
82 
63 About this deal
The H710 series of cases only supports EATX motherboards up to 10.7 inches in width. You may be able to install wider motherboards by removing the included cable bar, however this may negatively affect the aesthetics of the case and remove some cable management options such as tie-downs that are part of the cable bar. What length PCIe Riser Cable should I use to vertical mount a GPU in the H710i?
If you are looking for a recommendation, the NZXT PCIe Riser Cable is an excellent choice that not only meets these requirements, but also provides PCIe 4.0 compatibility. Can the Aer Trim be installed on the included fans? The NZXT H7 Flow is capable of handling not one, but two 360mm radiators — one on the front and another up top. The rear panel has a 140mm fan and radiator mount, atop of seven horizontal PCI slots. There aren't any vertical slots with the NZXT H7 series. Finally, we've got the single tempered-glass window panel, which showcases everything instead within the case. Otherwise, the H710i features a lot of the same features as the NZXT H700i. Plenty of intuitive cable cutouts and passthroughs, a roomy interior, quality finishes on all of the folded steel, and a lot of versatility as to where you can run your cables. Rear Cable Management and HDDs The plan being to get the H710 installed and running under ESXi 6.7 first and then upgrade to ESXi 7.0 later, once the H710 has settled in. PC cases not only protect your motherboard, processor, and graphics card from debris, dust, and other environmental hazards, but they also provide ventilation for your motherboard, processor, and graphics card, ensuring that everything stays nice and cool.The old H700i averaged 53.9C dT on the CPU torture test, a little less than two degrees warmer than the H710 result we just measured. The two cases are almost identical, but it’s been a long time since we wrote the first review: our test environment has become more consistent, there are always variations between fans, and the cases aren’t EXACTLY identical as we . We’re not concerned by the slight difference from our old results, but customers should NOT expect a significant improvement over the H700. This handy chart pulls the primary specifications of each of our H-series cases into one location! This should make cross-referencing and making a decision between them much easier. The H710i or the I version comes with the Smart Device and two pre-installed LED strips. Through CAM software, it can handle the integrated LED lighting settings and fan control.
Simple enough, power off the server, unplug and remove the H700 array controller and plug in the H710 array controller.For as long as I can remember, I've had love of all things tech, spurred on, in part, by a love of gaming. I began working on computers owned by immediate family members and relatives when I was around 10 years old. I've always sought to learn as much as possible about anything PC, leading to a well-rounded grasp on all things tech today. In my role at PCMag, I greatly enjoy the opportunity to share what I know. While temperatures were higher than they could have been with better access to air, NZXT was comfortable at the time to mix form with function. For the new NZXT H7 range, the company has redesigned how the cases both take and exhaust air. The NZXT H7 Flow is the biggest change here with the perforated front panel. The excellent cable management, better thermals, and updated design make the NZXT H7 series one to watch out for.
We’ll keep this section very brief since we’ve already reviewed most aspects of this case, but it’s worth mentioning a couple points again. First, the top and front panels are an enormous pain to remove. They’re held on with stiff clips, and the best method for defeating them is to yank the front panel violently from the bottom edge and then yank the top panel violently from the front edge. This MUST be done to remove the front filter, replace fans, or take out the radiator/fan tray at the top of the case, and it runs the risk of snapping the spindly 4.5cm clips or curving the panels and creating a gap between the front and top panels. The fan tray is still very nice, by the way--it’s held in with thumbscrews and can be flipped upside-down to move it higher away from the motherboard, and we’d like to see a similar tray at the front of the case.
Clean looks meet innovative design.
Obviously, the H7 Flow has a perforated front panel, allowing the case’s front fan (or fans) to intake air directly from the front. This maximises the H7 Flow’s air intake, making it the best performing H7 chassis in terms of cooling performance. Aesthetically, some users may prefer the H7 or H7 Elite, but for those who want the best cooling, the Flow will be the way to go. With the front panel being perforated, the H7 Flow’s right side panel can be completely closed off. Unlike the H7 and H7 Elite, the H7 Flow does not require a perforated right side panel for airflow, allowing NZXT to ship this model with a plain right side panel. The GPU average dT places the H710 between the H500M Mesh and the 570X on the chart. It’s not a bad score, and it’s again a couple degrees cooler than the H700i’s initial result of 52.5C dT. NZXT’s choice to ship with four fans is a valid way of making up the gap between it and cases with better airflow potential. Blender - CPU & GPU Isolated Renders
Great Deal 
New Comment