The bottom line is that you aren't going to feel any stinging or burning and there won't be any long term effects on your penis from using this kit. I texted James to see if he’d had success. Nope. He, too, struggled with the molding mixture, and his curved penis kept touching the sides of the tube. (If he’d been less impatient, he would’ve seen that the Clone-A-Willy kit offers a solution for men with curved penises.)

For those curious about what the molding powder is made from and if it is safe to dunk your penis in it, it's made predominantly from a sodium alginate mixture with a few extra things thrown in to help it set properly. This mixture is non-toxic, contains no silica, and is completely hypo-allergenic. I've googled all of the ingredients myself and they all show up in normal products ranging from toothpaste to cosmetic products. One particular ingredient, calcium sulfate, shows up in some building materials but that makes sense judging how it solidifies into a solid mold once everything is said and done. I went through the steps more or less without a lot of fuss, but there are a couple things I will share with you that might alleviate some of your worries. Press the tube against your body. The moulding gel will completely solidify in about two more minutes.Start your timer. Cut open the bag of white moulding powder, pour it into the bowl of water and start mixing. Stir no longer than 60 seconds. This kit is kind of like making pancakes except the batter is going to go bad in 90 seconds and you have to keep a boner the whole time,” James quipped. At least he managed to make a mold of the top half of his penis, allowing him to create a stubby replica of his half-boner, a neon purple “dome” that now sits on his girlfriend’s coffee table. Learn From My Mistakes After letting the impression set, take the two jars of silicone and mix them together as thoroughly as possible in a disposable container. I ended up not using a disposable container and I'll explain what I had to do as a result in the next section. Once the materials have been mixed together, pour out any water that has accumulated in the bottom of the mold and then add the mixture very slowly. You should remember that when you add in the vibrator the silicone will be displaced, so if you are going to use the vibrator don't fill it up all of the way. Tape around the edge of the tube. This will be pressed against your body, so you want it to be smooth.

In lieu of a Valentine’s Day gift, I wrote my girlfriend a letter explaining what I’d gone through. I finished the letter with, “I tried, I failed, but I will not give up. I need your help, my love.” All standard kits include 8oz of our 2-part 100% platinum cure silicone. The colored silicone is added to the clear base to make the mixture that goes into your mold. See the chart above to determine whether you will need extra silicone or an XL Vibrator. You then must hasten to shove your erect penis into the mixture "immediately," carefully avoiding touching the sides of tube. The tone of the directions—lighthearted and humorous—outline a process that required careful, diligent planning. As the impetuous man I am, directives such as, “Timing is very important!” stress me out, and I realized how unprepared I was for the Clone A Willy's litany of commands. How It Actually Worked Pour out any water that has accumulated in the bottom of your mould and slowly pour into the silicone. Your Clone A Willy Kit comes in an 11 x 2½ inch clear plastic tube, into which you will insert your penis. If your penis is 9” or larger, or you want to make a non-vibrating dildo, keep reading! You'll need some extra materials!All standard kits include 1 bag of molding powder. This is enough powder to make 1 mold of your penis (as shown in Fig. 2). If you want to be safe, buy a refill! For those who love things a little frisky and risky, the perfect gift has revealed itself. With the help of this Clone-a-Willy Kit, a perfect silicone copy of either your or your partner's penis can be immortalised. It's a great gift for Valentine's Day or anniversaries or ideal to help spice things up in the bedroom. Be sure to use this product with a water based lubricant. Read the instructions carefully before using this product to avoid any unwanted side effects or reactions. Spice Up Your Sex Life

My fantastic confidence in this endeavor and product waned considerably when I unfurled the poster-size directions. The four simple steps had transformed into more than a dozen, and the incredible specificity of each step had me in an immediate state of panic. The same applies to any spilled silicone. I didn't use a disposable bowl when I mixed the bags together and was at first stressed that I had to diligently wash out the still unhardened silicone from my wife's favorite mixing bowl. I later realized it would be smarter to just let the clone harden and peel it all off in one fell swoop and that's exactly what I did Insert the silicone and cardboard assembly into the centre of the filled mould so that the cardboard rests flat against the top of the tube. Ensure to leave enough space for the vibrator to be added, or the mould may overflow. Once the mould has gelled, remove your one-eyed trouser snake while leaving the mould inside the tube. To get the most detail, let this sit for four hours before moving on.Now the biggest challenge of the whole process is figuring out how you're going to stay hard for a full minute to ideally two minutes while you insert yourself inside the tube. I highly recommend you figure this out before you begin the process at all. Whether it be by having your spouse do a sexy dance in front of you, having a video queued up, it doesn't matter. Just know that you will have to be erect for a full two minutes with your penis inside of a tube full of molding mixture with only visual/mental stimulus available to keep you erect. I was fortunate enough to have my wife around to tease me, but if she was out doing errands I now think my final product would have been a tad on the chode side of things.