Wireless programmable room thermostats are easy to install, and most installers only need help with commissioning the system. First, remove the batteries from the transmitter unit and allow the screen to go blank. You can provide two-stage protection by installing a frost thermostat and a pipe thermostat to vulnerable pipework in garages or conservatories. This option has no schedule and controls by temperature only. You set your preferred temperature and adjust it with the + and - buttons. A home’s general temperature can be set to 21˚C, but installers can use TRVs to control the temperature in certain rooms, for example where part of a home has been developed to incorporate a ‘granny flat.’ Step by Step - Installing miGenie To learn more about TRVs, complete our e-learning module here Help customers to programme their system

Advise householders that concealing a TRV with furniture or behind a curtain will affect the performance of their system, making it less reliable as the TRV cannot accurately sense the temperature of the room. Advising customers on room thermostat settings The Green Premium eco-mark stands for complete, transparent, and easily available information about products Once you have drained down the system, you can start the installation. Remove the existing TRV by unscrewing the nuts on the 15mm copper pipe and the radiator tail piece. A frost protection thermostat is fitted in the same space as the boiler or most at risk part of the system, and works alongside the pipe thermostat, totally independently from all other timers and thermostats.Green Premium is the Schneider Electric eco-mark that brings more value to our customers and more growth to our company. There are known issues using Bluetooth with some later Apple devices. However the RETRY button should allow you to pair your Digistat within a few attempts. When a boost is selected, a timer symbol appears in the bottom right of the display and remains until the next event.

Put the SCR unit into its learn mode. Press and hold button number 1 and then do the same to button number 2. The red light will flash a couple of times before going out. Then release both buttons – the two LED lights should be on. In hard water areas it is more important than ever that TRVs are maintained to stop plastic degrading and valves failing. When used with an oil boiler the Digistat will allow the boiler to run without cycling for improved efficiency.

LP522Si

The miGenie gateway is designed to be placed on a flat surface and should be located next to the customer’s internet router. The red LED light will flash for approximately 7 seconds to tell you that the two units are initialising. This confirms that the radio signal is being sent and received. The Digistat is universal because it can be used as a fully-programmable thermostat or as a simple manual thermostat. In fact it contains 4 types of functionality: 7-day programming Hold the transmitter unit 2 metres away from the SCR unit and then replace the batteries in the transmitter.

If you find yourself working on a heating system that is exposed to the elements and is therefore likely to feel the full force of any cold weather, protecting the pipes against freezing can stop a system breakdown. When used with electric heating the Digistat cycles the heater at 12 cycles per hour to maintain room temperature and save money. However this auto-pairing process only lasts 2 minutes (to avoid issues of pairing with the wrong Digistat). If you find that the 2-minute auto-pairing period has expired, please follow the following process: The acclimatisation time for one of these units is approximately 4 degrees an hour or 1 degree every 15 minutes, meaning it could take several hours to reach the required temperature for the first time. Finding a compatible replacement programmer

Digistat+3RF Si

The app will allow complete control over time and temperature in individual rooms around the home, wherever and whenever you wish. When batteries are running low, a low battery icon will flash in the display. During this time, miGenie will function normally.

The receiver unit should be positioned 300mm away from any metal objects such as the boiler or a microwave or any large obstructions like solid walls that will affect the signal being sent from the transmitter to the receiver. Replacing a timeswitch with a wireless programmable thermostat

These settings appear in the installer menu and it is important to select the setting for your heat source: gas boiler (default), oil boiler, heat pump, or electric heating Our Green Premium eco-mark encompasses a broad range of environmental criteria, meeting and exceeding international regulations and industry standards: Yes, there is a Digistat to suit both types of boiler – try our product selector to find the right one for you. Do I need an OpenTherm boiler to use Digistat? To swap between Heating and Hot Water on the thermostat press the setting button (cog symbol) to open this open.