For the different types of CV boot clamps found, the first one is a normal sliding saddle with a ball that holds it tight, and the other is flat, and it has to be hooked together and crush the section binding it upward to pull it tight. Pull the clips together as tight as you can till one of the hooks enter one of the holes on the trail, further away from the raised portion, and holds the clip in place. This can be done using your finger/thumb pressure or using a big pair of water-pump pliers. Then pinch the raised portion’s sides to compress them close together; this causes it to tighten the clip against the boot. Q: Can you reuse the CV boots clamp? Remember to always put on your safety wears on before carrying any major or even minor repair procedures. I suggest that you buy a pair of sunglasses and some rubber gloves. If possible, a coverall. These safety kits will help avoid any form of injury that might occur when carrying out a repair. Moreover, it helps protect your skin from any toxic or harmful fluid that might spill, like the brake fluid, for instance. Voor gebruik met een luchtcompressor. Werkt bij 58 - 101 psi (4 - 7 bar) Standaard 1/4" BSP-verbinding. Two way jaws offer a choice of clamping positions at 90° to each other, ideal for use in restricted areas.

Tweewegbekken bieden een keuze aan klemposities onder een hoek van 90° ten opzichte van elkaar, ideaal voor gebruik in beperkte ruimtes. A cable tie, which is also known as a hose or zip tie, or ty-rap, can be used as your CV boot clamp alternative. They are cheap and easy to use in fastening or holding items together. They prevent grease from coming out and can also be used to tighten clips. Final Words Once you have your boot clamp well-placed around the CV boot, grab your Lisle CV boot clamp plier and use its metal grip to hook the end of your boot clamp, then pull outward until it’s tightly fixed on the boot clamp. After making sure it’s tight, bend the free end of the clamp over the metal clasp. Please do not apply too much effort in pulling the end of the clamp outward; this can damage the clamp. Q: How do you attach boot clips? For fitting stainless steel bands on drive shafts where a torque setting is specified. Suitable for use with 3/8" torque wrench, including Laser Part No. 1342.Can be used by hand with a 3/8" standard ratchet (such as Part No. 6667) or swivel head ratchet (Part No. 6957) when a specific torque setting is not required. It necessary you get your simple tools close by, so you don’t have to run about getting tools that you urgently need during a repair. It is advisable that you get a tools box, especially for mechanics who are constantly repairing a lot of vehicle systems. Step 3: Raise your vehicle. This article will enlighten you on how best to tighten your boot clamp as effectively as using any special tool. How to tighten CV boot clamp without tool step by step After you have raised your vehicle to a moderate level, you can now wholly unscrew your lug nuts and axle nuts so you can remove the wheels. Always make sure you are careful. Step 5: Take-off your steering linkage You need to first take off the tie rod. If you notice a bad tie rod, you can replace it now. To remove the tie rod, use your pliers to detach the cotter pin. Then bend the cotter pin to make the ends straight, then use the rounded end to pull out the tie rod.

utiliser sur les soufflets intérieurs et extérieurs. Kits de soufflets de cardan universels coupés sur mesure disponibles, voir les références Connect 37660 (pour diamètre d'arbre 18 - 26 mm) et 37661 (pour diamètre d'arbre 27 - 37 mm). CV boot clamp pliers with 3/8" torque drive for VW Group, Vauxhall, Opel, Ford and others. Designed to fasten high-strength stainless steel boot clamps that require a higher compression force to be correctly fitted. The pliers feature a 3/8" drive for use with a torque wrench for precision hose tightening, ensuring compliance with manufacturer specified torque settings - typically between 23Nm and 30Nm. The 90° two way jaw system allows the user more access points for clamp tightening, a useful feature in confined suspension and driveshaft areas. The rugged construction and smooth action of the pliers makes them ideal for professional use. Pull the thread outward to tighten the boot clamp around your CV boot. Use your needle nose plier to do this properly. This will tighten the clamp around your CV boot and create pressure on the metal clasp. With safety wears on, you can perform any repair without directly exposing your skin to any harmful substance or fluid you might handle during repairs. Step 2: Get your tools ready. Then thread the end of the boot clamp, which has holes under your metal clasp. The metal clasp is fixed to your clamp to ensure the clamp is well circled around your boot. Place the boot clamp to the left side of your CV boot.You know also try using car lifts, it makes lifting your vehicle easier. Just make sure the adaptors are well placed in the recommended positions in your vehicle before lifting your vehicle and the vehicle should be placed in such a way that it is evenly raised by the lift. Also, ensure you inspect the lifts for fault and know the load limit it is designed to carry before using it. Step 4: Detach the lug nut and wheel For use on inner and outer boots. Cut-to-size universal CV boot kits available, see Connect Part Nos. 37660 (for shaft diameter 18 - 26mm) and 37661 (for shaft diameter 27 - 37mm). CV-klemtang met 3/8" aansluiting voor VW Group, Vauxhall, Opel, Ford en anderen. Ontworpen om zeer sterke roestvrijstalen slangklemmen vast te zetten die een hogere compressiekracht vereisen om correct te worden gemonteerd. De tang heeft een 3/8" aansluiting voor gebruik met een momentsleutel voor het nauwkeurig aandraaien van slangen, zodat de door de fabrikant gespecificeerde koppelinstellingen worden nageleefd - meestal tussen 23Nm en 30Nm. Het 90° tweewegbeksysteem geeft de gebruiker meer toegangspunten voor het vastdraaien van de klemmen, wat handig is in krappe ruimtes bij ophangingen en aandrijfassen. Door de robuuste constructie en soepele werking is de tang ideaal voor professioneel gebruik.