Only apply in double figure temperatures and when the weather is set to be dry for at least the minimum drying time displayed on the tin. Single figure temperatures, damp or wet conditions could adversely affect the application and final finish of the product Customer review:"Last used 2 years ago and finish lasted well. Very good product and so simple to apply by brush. Slightly more expensive but would recommend for quality." The Oil will not restore the natural colours of the wood and if you apply a coloured oil to the silvered wood it will not look as expected. The silvered wood has also changed in composition as it has been impacted by the UV and this will in turn impact on how it takes on any product applied. Once restored and dry, I would recommend a wipe over with Methylated Spirits also and then a test area to ensure you like the finish that will be achieved it is ready for which ever oil you choose to protect with, a test area is always recommended first and if you have any further questions I am here to help.

Thank you for getting in touch with your question. It is a common question asked for beautiful tropical hard woods such as Ipe, Balua and Iroko. Jatoba is a less common one, however if it is anything like the others it will require a period of weathering. Tropical hardwoods tend to have a naturally high oil content when they are relatively new, these oils will prevent the uptake or adhesion of any product that you try to apply. So a weathering period to allow these oils to naturally disperse is the recommendation. Whether you want an easy to complete maintenance that needs regularly redoing or a more comprehensive one that you can apply and forget for a few years I am sorry for the delay in response, it is a super busy time here at Wood Finishes Direct. A stain or paint is a surface sealer and is likely to, over time, peel and flake, if the treatment appears to be lifting it is likely that this is the finish you have and this can be removed with a pressure washer or stripper product such as the Paint Panther Paint and Varnish Remover Thank you for this incredibly helpful article and for your detailed responses. It’s awesome to see a business taking the time to provide customers with such helpful information.

Steps to take before applying decking oil

Different species of wood will absorb oils at a different rate and in turn the pigment and so you will get the same tone but perhaps with a slight variance in intensity of colour. Test areas will show what colours can be achieved. However, specific information about the ease of application and enhanced appearance is not provided for the Manns Premier UV in the given details. Depending on individual needs and preferences, customers may prioritize the UV protection and weather resistance provided by the Manns Premier UV 5L Clear or the comprehensive features of the RONSEAL Ultimate Natural 5L, including its natural look and unique penetrating formula. It also brings out the natural shade of wood on various surfaces like fences, sheds, and hot tubs. While the RONSEAL Ultimate Natural 5L offers a “natural look,” the Liberon Clear Protection is specified as providing a “clear finish.” The choice between the two would depend on personal preferences regarding the desired appearance and the additional feature of UV protection provided by the Liberon oil. Thank you for getting in touch. I can make some recommendations for a protective product, however anything you apply may darken the wood slightly, much like water does. Over time this could fade down although you may not be able to fully maintain that silvered appearance. Ahandytip before we get started is to keep an eye on the weather forecast as we are going to need a couple of clear days to get the project done properly trust me it’ll be worth it in the end.

It would need a little bit of experimentation first to get the right result, it may be that you only require a very small amount of the coloured oil added to the clear, it is vital to thoroughly mix them together. So small ratio measures first and tests on your wood, until you get the desired result and then you are able to mix up a larger quantity in the same ratio to complete the project. This will help you to control the colour a bit more for getting the lighter result. A slight concern I had was the tendency of the product to clog when left in a spray applicator. However, with a bit of cleaning and attention, it can still be used effectively in this manner. We are set up to do a big deep clean with oxygen bleach and want to apply something that is as indestructible, low maintenance and long lasting as possible. Basically hoping to get it done and forget about it for as many years as possible!

As I’ve discovered, some oils offer better water resistance, while others provide enhanced UV protection. The appearance of the finish, such as matte or glossy, is also worth considering when making my decision.

Oils and Varnishes are not compatible except in very rare situations. So I would not advice it, the varnish is unlikely to adhere to the oils surface. If you need any further advice on your project please do not hesitate to get in touch. As the wood is Balau there may be a naturally high oil content already and a test area first to ensure the wood will accept further oil is strongly recommended. You could wipe down the surface of the wood with Methylated spirits first as this will encourage the wood to accept more oil. Then two thin coats are all that is required. What a great project !! To achieve those colours you will need to look at some of the Osmo products, here at Wood Finishes Direct we nearly always recommend oils for exterior protection, they are durable and easy to apply and maintain and will not peel and flake. You could have a look at the Osmo Country Colour this is a more opaque finish with the colours that you require, but at the same time can allow the wood to look and feel fairly natural. I’ve got a full tin of Ronseal Multipurpose Wood Treatment (which is clear and solvent-based). Is there any reason why I shouldn’t use that rather than the Barrettine product?

Test areas are always recommended to ensure you like the look to be achieved and if you use a colour then this will also increase the UV protection to the wood and slow down the silvering process. Can reduce the visibility of the wood grain due to the pigmented film between the timber and the surface